Myth-bust: “It’s off, so it’s not using power.” 👀 Many TVs, printers, and chargers still sip energy on standby. Try a smart power strip tonight—one button (or auto-sense) can cut phantom loads + lower your bill. What’s always plugged in? #InergySystems #EnergySavings

Quick win: wrap a water heater blanket + insulate the first 6–10 ft of hot water pipes. Less heat lost in the garage/basement = the heater cycles less, bills often drop. What temp is your water heater set to right now? #InergySystems #Efficiency

Try this tonight: set your water heater to 120°F (and add an insulation blanket if it’s older). You’ll cut standby losses and still have plenty of hot water. What’s yours set to right now? #InergySystems #Efficiency

Try “night mode” for your home or shop: set TVs, PCs, printers, and game consoles to auto-sleep + use a smart power strip for the entertainment/desk cluster. It cuts phantom load that sneaks into the bill. What device do you suspect is the worst? #InergySystems #EnergySavings

Try this tonight: set your water heater to 120°F (and “Vacation” mode when you’re away). Less standby heat loss = lower bills, with the same hot showers. What’s your water heater set to right now? #InergySystems #EnergySavings

Try this tonight: set your water heater to ~120°F (and add an insulating blanket if it’s older). It often trims standby losses without killing comfort. What’s your current setpoint—ever checked it? #InergySystems #Efficiency

Try this tonight: set your water heater to 120°F (and use vacation mode if you’re away). It can cut standby heat loss without changing your routine. Want a reminder to check it seasonally? #InergySystems #EnergySavings

Try this tonight: set your water heater to ~120°F (unless you need hotter). It often cuts standby heat loss and still keeps showers comfy. Want a quick checklist to see if yours is set too high? #InergySystems #Efficiency

Quick win: add door sweeps + fresh weatherstripping to exterior doors. If you can feel a draft, your HVAC is paying to heat/cool the outdoors—sealing those gaps often improves comfort fast. What’s your leakiest door? 🚪 #InergySystems #Efficiency

Try this tonight: set your water heater to 120°F (most are higher than needed). It can cut standby losses and still keep showers comfy. If you have a “vacation” mode, use it when you’re away. What’s your current setting? #InergySystems #EnergySavings

Quick win: wrap your water heater + the first few feet of hot water pipe with insulation 🧥 It cuts standby heat loss so you’re not paying to reheat water all day. Weekend project—want a link to a simple checklist? #InergySystems #Efficiency

Quick win for home + small biz: add a smart power strip to your TV/office/point‑of‑sale setup. It cuts “always on” standby loads by turning accessories off when the main device sleeps. What plug-in cluster bugs you most? #InergySystems #EnergySavings

Try this tonight: set your water heater to 120°F (and insulate the first few feet of hot water pipe if you can). You’ll waste less heat between uses, so showers feel the same but bills can drop. What temp is yours set to? #InergySystems #Efficiency

Try this tonight: set your smart thermostat to “Auto” and widen the temp range a couple degrees (e.g., 68–74). HVAC runs less, comfort often stays the same, and bills can drop. What’s your current setpoint? #InergySystems #Efficiency

Try this tonight: set your water heater to 120°F (and add a simple timer if your schedule is predictable). You’ll cut standby losses while still getting plenty of hot water. What’s your current temp set to? #InergySystems #Efficiency

Try this tonight: set your thermostat to “auto” (not “on”) and bump the fan to circulate only when heating/cooling runs. You’ll cut unnecessary run time while staying comfy. What temp do you set for sleep? #InergySystems #Efficiency

Try this tonight: set your water heater to ~120°F (unless your manual says otherwise) and add a simple insulation blanket if it’s in a cool garage/basement. Less standby heat loss = lower bills. Have you checked your setpoint lately? #InergySystems #Efficiency

Try this tonight: set devices to “sleep” + use a smart power strip for your TV/desk setup. Phantom loads can quietly add up—even when you’re “off.” What’s one thing you leave plugged in 24/7? #InergySystems #EnergySavings

Try this tonight: set your water heater to 120°F (and add a cheap insulation blanket if it’s in a garage/basement). It can cut standby heat loss without killing comfort. What’s your current setting? #InergySystems #Efficiency

Try this tonight: set your water heater to 120°F (most are higher by default). Less standby heat loss = lower bills, and you’ll often still have plenty of hot water. What’s yours set to right now? #InergySystems #Efficiency